What To Do If Your Water Heater Unexpectedly Stops Working
What To Do If Your Water Heater Unexpectedly Stops Working
Blog Article
The article author is making a number of great points about How to Troubleshoot and Repair an Electric Water Heater in general in this post down below.
Numerous modern-day residences make use of an electric hot water heater for their heating system, because of its ease and convenience of use. However, much like any other electric appliances, issues might arise with its usage, suddenly. It can be actually frustrating to get up to a cool shower instead of a hot one or having your bathroom with water that isn't hot sufficient or perhaps also hot. Whatever the situation may be, hot water heater troubles can be quite stressful. Luckily, we have actually made a list of possible options to your hot water heater issues. There are a number of aspects that can cause most of these troubles, it could be an issue with the power supply, the electrical heating element, or the thermostat. Before doing anything, guarantee you switch off the major power supply for safety. Whatever the problem is, getting it repaired must not posture excessive of a problem if you adhere to these actions:
Call A Professional:
If after replacing all defective parts as well as resetting your temperature level, the hot water heater still isn't functioning, you might require to speak to an expert plumber for a specialist point of view. The trouble with your heating system could be that the cold and hot taps have been switched or it may be undersized for the amount of hot water needed in your home. Whatever the case may be, a professional plumber would aid fix the trouble.
Examine Your Power Supply:
As standard as this might appear, it is really essential. Without ample power, your hot water heater will certainly not work. So the first thing to do when your water unexpectedly retires is to verify that it isn't a power issue. Inspect if the fuse is blown out or the circuit breaker tripped. If the circuit breaker is the concern, merely transform it on and off once again. Replace any broken or damaged fuse. Examine the device with power after these adjustments to see if it's currently working.
Check Your Thermostat:
If your water heater still isn't functioning or the water appearing isn't warm enough, you may need to examine the temperature level setups on your upper thermostat. Ensure the breaker is turned off prior to doing anything. Open the access panel and also press the red switch for temperature level reset above the thermostat. This should aid heat up the water. Turn the circuit breaker back on and also examine if the problem has actually been solved.
Inspect the Heating Element in the Hot Water Heater:
If it's not a power issue, then try looking into your burner if it is still functioning. Evaluate each of your heating elements to ensure the issue isn't with any of them. If any one of them is malfunctioning, replace that component and after that check whether the warm water is back on.
Final thought
Water heater issues are not always significant. A number of them are due to small problems like a blown fuse or worn-out burner. Replacing the faulty components should suffice. Nevertheless, if you are still unable to address the issue, give a call to your nearest plumber to find to get it fixed.
What Would Cause My Electric Water Heater to Stop Working?
Your water heater is one of the most forgotten-about appliances in your home—until it quits working. Once you realize that there’s no hot water, the water heater jumps up to become the most noticeable appliance you have. No one in your family will be happy until you get the water heater fixed.
To fix an electric water heater as soon as possible, follow the troubleshooting advice discussed below.
Basic Water Heater Troubleshooting
Fortunately, you may be restore the hot water supply simply by resetting the house circuit breaker for the water heater. A tripped circuit breaker is one of the top causes of water heater failures. Shut the hot water heater breaker off then turn it back on. Give the water heater a half hour to heat up (if it’s working) and then check for hot water through one of your faucets.
If you get hot water after resetting the breaker, then the problem may be fixed if the breaker inadvertently tripped and it doesn’t continue tripping.
If the water heater breaker trips again, then you’ll likely need to have a service technician examine and repair the water heater. The service technician will check the circuit breaker and electrical supply wiring for the water heater. A short in the supply wiring or a bad circuit breaker could be causing the breaker to trip. An internal failure such as a broken heating element can also cause the breaker to continue tripping.
When resetting the water heater circuit breaker doesn’t work at all, then the water heater may be getting power while an internal water heater failure is causing the problem.
Conduct Advanced DIY Water Heater Troubleshooting
If the water heater doesn’t work after resetting the high-temperature limit switch, then you’ll need to either conduct some advanced water heater troubleshooting or have a service technician diagnose and repair the water heater failure.
Sears Technicians created a safe and highly-successful DIY advanced troubleshooting video to help you determine the cause of a water heating failure if you want to try to fix the problem yourself. Follow the advice in this video to find and fix the cause of the heating failure on your own:
The video begins with the basic troubleshooting described in the first 2 sections described above. It then goes on to guide you through checking water heater components to safely find the cause of the water heating failure.
If you get to a point in the troubleshooting where you’re not completely confident that you can safely continue, schedule a service technician to diagnose and repair the water heater.
The DIY water heater troubleshooting shown in the above video differs from the diagnosis techniques that service technicians typically use when examining a water heater to find the cause of a heating failure. Safe DIY troubleshooting doesn’t rely on live voltage checks while service technicians often use live voltage checks to quickly find the cause of water heater failures.
While many DIY’ers have been able to find the cause of water heater failures using troubleshooting advice shown in the video, some failures such as a bad circuit breaker can only be found using live voltage checks which should only be conducted by a trained service technician.
Sears Technicians have the training, tools and expertise to quickly find the cause of a water heater failure. Rely on our technicians to diagnose and repair your water heater or any other appliance in your home that quits working.
While the technician is in your home, take advantage of appliance Cleaning & Maintenance offers that the tech discusses with you. Keeping your appliances well-maintained will help them work more efficiently and last longer. Regular professional maintenance will also help prevent costly breakdowns of the appliances you depend on every day.
https://www.searshomeservices.com/blog/what-would-cause-my-electric-water-heater-to-stop-working
I was guided to that article on No Hot Water — Water Heater Repair through a good friend on another web page. Sharing is good. You never know, you could be helping someone out. I love reading our article about No Hot Water — Water Heater Repair.
Browse Our Site
Report this page